SHOW FILTERS
377

DIY Wedding Ideas

  • Photo: This Modern Romance 

    Photo booths are all the hype at weddings, and why not? They keep your guests entertained! Here's our step-by-step guide to make your own. 

    Materials Needed:

    Digital point-and-shoot camera Camera tripod  Remote shutter release  Backdrop Props 

    The Camera - Place a digital point-and-shoot camera on top of an extended tripod at eye level, turn on the flash and connect a remote shutter release so guests can take their own photos. 

    Photos (from left to right): This Modern Romance and Anjuli 

    The Backdrop - Pick a piece of fabric that you can hang. If you're having an indoor wedding, pin it to a wall, or if you're having an outdoor wedding hang from curtain rods, secure with rope, and nail into the ground. 

    Photos (from left to right): Shelly Kroeger Photography and Birds of a Feather

    The Props - Go on a scavenger hunt! Use props from your own home (like scarves, hats, glasses, frames). Or make your own from paper (lips, mustaches, ties). Even provide chalkboards or dry erase boards for guests to write messages on. 

    Photo: This Modern Romance 

    The Location - Choose an area that doesn't get crowded in the reception, but is still easily accessible. 

    Photo: This Modern Romance

    The Extras - After the wedding is all said and done, you're back from your honeymoon, and all the gifts are unwrapped and put away, go through the camera's SD card and save the ones you'd like to put into an album. Those memories will last a lifetime! 

     

     

    19
  • By: Victoria Hudgins

    This DIY packaging is a fresh and modern way to present small favors to guests.         Fill each cocoon with something fun to keep your guests busy (like these bright and nostalgic finger pops) and something sweet to snack on.   Materials: 1/2 craft glue- 1/2 water mixture Large spool of embroidery thread Balloons (1 balloon for every 2 favors)   Instructions:   1. Blow up your balloons and tie a length of thread to the end of the balloon.   2. Begin wrapping thread around the balloon, the messier the wrap the better.   3. Once you have a good covering over the entire balloon, dip a brush into the glue mixture and coat the entire balloon. Hang the balloon by its end to dry. Note: You could also use liquid fabric stiffener for this step in the project, just fill a large bowl and completely dip your wrapped balloons in.     4. Once dry, cut the balloon in half at the center width. Each balloon will make two separate cocoon wraps.      5. Gently pop each balloon and pull away from the fabric. Fill your wraps and tie together with a ribbon and simple tag.     6. Rest each favor on a place setting for a creative, modern touch.  
    5
  •  

    By: Chelsea Fuss     You will need: White paper bags Acrylic paint Paintbrush Number stencils (for table numbers) Painter's tape LED votive lights For the striped bags: Place strips of painters tape horizontally or vertically on flat bags, Measure to space them about an 1.5" a part. Paint in between the tape and then let it dry. Take the tape off when dry. Open bag and place LED lights inside.       For Numbered bags: Place stencil on flat bag and paint. Once dry, open bag and place light inside!     Line a stairway with the luminaries, mix and match them for a centerpiece or line your wedding aisle with them!     The hand-painted stripes look gorgeous when illuminated.     Total cost is $1.50 a piece including lights!     These hand-painted luminaries make a charming wedding decoration and a cheaper alternative to lanterns. Enjoy!   (photos by Chelsea Fuss)
    7
  •  

    By: Danyelle Mathews   Creating charming escort cards for your wedding doesn't have to take a lot of time or resources. Simply gather a few basic, inexpensive supplies to produce this budget-savvy, casual-chic concept.      Supplies: Manilla shipping tags Chalkboard paint Foam paintbrush   Step One Arrange your tags on a large work surface     Step Two Dip the foam paintbrush into the chalkboard paint and apply one brushstroke to each tag.     Step Three Allow the paint to dry completely, then write guests names and seating information on the tags with chalk.     Step Four Display the tags using a fabric backdrop, coordinating yarn or string and wooden clothespins.     {Photos by: Danyelle Matthews}
    6
  • By: Victoria Hudgins 

    These trendy, crafted flowers will look amazing in bouquets or décor!     I was inspired by a pre-made version and quickly realized how easy the flowers are to whip up! Consider making a bouquet for everyone in your wedding party or a few dozen to construct a ceremony backdrop.   Materials: Extra long crepe paper in the colors of your choice Floral wire Scissors Green floral tape     Step One: Working horizontally, begin by folding your crepe paper in a small accordion fold. Use your finger to gently roll over the top 1/4 inch of the paper giving it a pretty curled edge.     Step Two: Place a floral wire half way up the paper at one end and begin rolling the paper up TIGHTLY. To get the exaggerated effect, focus on tightly gathering the bottom 1/4" of the paper, letting the top open wide. Tie off the flower at the base of the 'stem' with a simple thread and knot. It helps to have a second pair of hands for this part!         Step Three: Wrap the entire stem with green floral tape.         {Photos by Victoria Hudgins}
    12
  •  

    by Olivia Kanaley     Supplies: Wire berry garland (one 4 ft garland makes 5-6 wreaths) Natural floral wire Shipping tags Wire cutters White glue Paintbrush Clear glitter     Instructions: 1. Cut an 18" length of floral wire using wire cutters and form it into a circle about 2.5" in diameter as shown. 2. Snip sprigs from a wired berry garland and wrap them around the floral wire frame. 3. Continue until the wreath has berries all the way around.     4. Brush on white glue with a paintbrush and sprinkle with clear glitter. Let dry.     5. Tie on a tag with guest's name and table number.     Your escort wreaths will be a memorable memento from your winter wedding!    
    2
  • Project & Photos By: Victoria Hudgins

    Looking for a less traditional cake topper for your wedding? These vintage fabric stars will bring a dose of bright charm to your cake or dessert bar.     Materials: To make them, you'll need basic star frame(s), mod podge, fabric, and scissors. Small cardboard star frames are available at your local craft store, while larger metal frames can be readily found at thrift stores or at many big box stores.     Materials (cont.): Find a fabric that coordinates with your wedding day. Search Etsy for a wide variety of pretty vintage florals or check your local fabric store for vintage replica fabrics.     Step One: Cut your fabric to the approximate size of your star and dredge it in a bowl of Modge Podge until completely wet. Place the fabric on top of your mold and use your fingers to gently shape it into form. Let dry overnight.     Step Two: Once dry, cut the fabric closer to the frame shape and turn over. Secure any extra fabric in the back with glue.     Step Three: Use wood glue to attach a stick to the backside of a large star frame. Many smaller frames come sold with small wooden sticks already attached.     Display Tip: Place one large star in your cake for a bold bright touch or scatter smaller stars atop cakes, cupcakes and desserts.          

     

    2
  • Photos By: Jordan Ferney

    Materials: 2 feet of 18" Russian Veiling Comb Thread and Needle Ruler Scissors  

    Important Note: There are two sides of the veiling: finished and unfinished. You want the finished end to run across your face NOT the unfinished side.

    Starting at point A start sewing in and out of the diamond shapes to gather the fabric. You'll continue sewing in and out on all sides until you get to point B.     Sew it to a hair comb.     After you attach it in your hair on the side of your head with bobby pins, then add an embellishment like a flower or feather to cover the comb.     Birdcage veils are made out of Russian Netting or Russian Veiling which is a millinery material. You can usually find it at a really good fabric store or online.     The veiling usually comes in three lengths 9" 12" and 18".     Isn't she gorgeous! If you just want a little coverage over your hair you want 9".     If you want it to cover your eyes, you'll want 12" and if you want it to cover your nose or chin you'll want the 18" veiling (cut it down to 16" to cover the nose.)     It comes in almost every color and you can also find veiling with chenille dots or pearls if you wanted to add embellishment in that way.     Inspired by precious birdcages everywhere! Enjoy!

     

     

    15
  •  

    Photos by: Chelsea Fuss     You will need:  A paper photo album (we used this one from Kolo) works great!  About 1/2 a yard of fabric  Ribbon or string Photo corners Fabric glue Scissors An iron     Take out the ribbon the photo album came with and separate the paper cover and set the pages aside.     Cut a piece of fabric that will cover the outside and inside of the paper photo album cover.     Press the fabric over the paper. Secure the fabric on the inside. fold over raw edges, press them and then secure them to the cover with glue.     Tie together the pages and secure them to the fabric cover with string or ribbon.     For the window opening, cut an X in the fabric and glue the excess fabric underneath the cover.     Secure photos with photo corners.      
    2
  •  

    Concept by: Victoria Hudgins Photos by Erin Holland   Add a dash of confetti to your party in the form of a chandelier! This looks fabulous hung in multiples on top of a dessert bar, or hung individually as centerpieces.     In fact, you can turn your confetti chandelier into a 'cake topper,' who says that a 'topper' has to be placed directly on top of the cake?     Cut out one inch confetti rounds from colored paper. We used about 120 rounds for this installation. I would suggest using a monotone color scheme or 4-5 coordinating colors on each hoop.     Thread the confetti dots together. Begin at the top, leaving enough thread to attach the string to an embroidery hoop. Have your hot glue gun ready and place a tiny drop of glue on the bottom of each dot to hold it in place.     Using an embroidery hoop, tie four to six strings across the top in a criss cross pattern.     One at a time, tie the strands of confetti dots onto the hoop and string base. You can paint or adorn the hoop as needed to match your wedding décor.     Hang the installation above a cake or elsewhere; adjust the length of the strands for just the right balance.      
    17
  • Photo: This Modern Romance 

    Photo booths are all the hype at weddings, and why not? They keep your guests entertained! Here's our step-by-step guide to make your own. 

    Materials Needed:

    Digital point-and-shoot camera Camera tripod  Remote shutter release  Backdrop Props 

    The Camera - Place a digital point-and-shoot camera on top of an extended tripod at eye level, turn on the flash and connect a remote shutter release so guests can take their own photos. 

    Photos (from left to right): This Modern Romance and Anjuli 

    The Backdrop - Pick a piece of fabric that you can hang. If you're having an indoor wedding, pin it to a wall, or if you're having an outdoor wedding hang from curtain rods, secure with rope, and nail into the ground. 

    Photos (from left to right): Shelly Kroeger Photography and Birds of a Feather

    The Props - Go on a scavenger hunt! Use props from your own home (like scarves, hats, glasses, frames). Or make your own from paper (lips, mustaches, ties). Even provide chalkboards or dry erase boards for guests to write messages on. 

    Photo: This Modern Romance 

    The Location - Choose an area that doesn't get crowded in the reception, but is still easily accessible. 

    Photo: This Modern Romance

    The Extras - After the wedding is all said and done, you're back from your honeymoon, and all the gifts are unwrapped and put away, go through the camera's SD card and save the ones you'd like to put into an album. Those memories will last a lifetime! 

     

     

    19
  • By: Victoria Hudgins

    This DIY packaging is a fresh and modern way to present small favors to guests.         Fill each cocoon with something fun to keep your guests busy (like these bright and nostalgic finger pops) and something sweet to snack on.   Materials: 1/2 craft glue- 1/2 water mixture Large spool of embroidery thread Balloons (1 balloon for every 2 favors)   Instructions:   1. Blow up your balloons and tie a length of thread to the end of the balloon.   2. Begin wrapping thread around the balloon, the messier the wrap the better.   3. Once you have a good covering over the entire balloon, dip a brush into the glue mixture and coat the entire balloon. Hang the balloon by its end to dry. Note: You could also use liquid fabric stiffener for this step in the project, just fill a large bowl and completely dip your wrapped balloons in.     4. Once dry, cut the balloon in half at the center width. Each balloon will make two separate cocoon wraps.      5. Gently pop each balloon and pull away from the fabric. Fill your wraps and tie together with a ribbon and simple tag.     6. Rest each favor on a place setting for a creative, modern touch.  
    5
  •  

    By: Chelsea Fuss     You will need: White paper bags Acrylic paint Paintbrush Number stencils (for table numbers) Painter's tape LED votive lights For the striped bags: Place strips of painters tape horizontally or vertically on flat bags, Measure to space them about an 1.5" a part. Paint in between the tape and then let it dry. Take the tape off when dry. Open bag and place LED lights inside.       For Numbered bags: Place stencil on flat bag and paint. Once dry, open bag and place light inside!     Line a stairway with the luminaries, mix and match them for a centerpiece or line your wedding aisle with them!     The hand-painted stripes look gorgeous when illuminated.     Total cost is $1.50 a piece including lights!     These hand-painted luminaries make a charming wedding decoration and a cheaper alternative to lanterns. Enjoy!   (photos by Chelsea Fuss)
    7
  •  

    By: Danyelle Mathews   Creating charming escort cards for your wedding doesn't have to take a lot of time or resources. Simply gather a few basic, inexpensive supplies to produce this budget-savvy, casual-chic concept.      Supplies: Manilla shipping tags Chalkboard paint Foam paintbrush   Step One Arrange your tags on a large work surface     Step Two Dip the foam paintbrush into the chalkboard paint and apply one brushstroke to each tag.     Step Three Allow the paint to dry completely, then write guests names and seating information on the tags with chalk.     Step Four Display the tags using a fabric backdrop, coordinating yarn or string and wooden clothespins.     {Photos by: Danyelle Matthews}
    6
  • By: Victoria Hudgins 

    These trendy, crafted flowers will look amazing in bouquets or décor!     I was inspired by a pre-made version and quickly realized how easy the flowers are to whip up! Consider making a bouquet for everyone in your wedding party or a few dozen to construct a ceremony backdrop.   Materials: Extra long crepe paper in the colors of your choice Floral wire Scissors Green floral tape     Step One: Working horizontally, begin by folding your crepe paper in a small accordion fold. Use your finger to gently roll over the top 1/4 inch of the paper giving it a pretty curled edge.     Step Two: Place a floral wire half way up the paper at one end and begin rolling the paper up TIGHTLY. To get the exaggerated effect, focus on tightly gathering the bottom 1/4" of the paper, letting the top open wide. Tie off the flower at the base of the 'stem' with a simple thread and knot. It helps to have a second pair of hands for this part!         Step Three: Wrap the entire stem with green floral tape.         {Photos by Victoria Hudgins}
    12
  •  

    by Olivia Kanaley     Supplies: Wire berry garland (one 4 ft garland makes 5-6 wreaths) Natural floral wire Shipping tags Wire cutters White glue Paintbrush Clear glitter     Instructions: 1. Cut an 18" length of floral wire using wire cutters and form it into a circle about 2.5" in diameter as shown. 2. Snip sprigs from a wired berry garland and wrap them around the floral wire frame. 3. Continue until the wreath has berries all the way around.     4. Brush on white glue with a paintbrush and sprinkle with clear glitter. Let dry.     5. Tie on a tag with guest's name and table number.     Your escort wreaths will be a memorable memento from your winter wedding!    
    2
  • Project & Photos By: Victoria Hudgins

    Looking for a less traditional cake topper for your wedding? These vintage fabric stars will bring a dose of bright charm to your cake or dessert bar.     Materials: To make them, you'll need basic star frame(s), mod podge, fabric, and scissors. Small cardboard star frames are available at your local craft store, while larger metal frames can be readily found at thrift stores or at many big box stores.     Materials (cont.): Find a fabric that coordinates with your wedding day. Search Etsy for a wide variety of pretty vintage florals or check your local fabric store for vintage replica fabrics.     Step One: Cut your fabric to the approximate size of your star and dredge it in a bowl of Modge Podge until completely wet. Place the fabric on top of your mold and use your fingers to gently shape it into form. Let dry overnight.     Step Two: Once dry, cut the fabric closer to the frame shape and turn over. Secure any extra fabric in the back with glue.     Step Three: Use wood glue to attach a stick to the backside of a large star frame. Many smaller frames come sold with small wooden sticks already attached.     Display Tip: Place one large star in your cake for a bold bright touch or scatter smaller stars atop cakes, cupcakes and desserts.          

     

    2
  • Photos By: Jordan Ferney

    Materials: 2 feet of 18" Russian Veiling Comb Thread and Needle Ruler Scissors  

    Important Note: There are two sides of the veiling: finished and unfinished. You want the finished end to run across your face NOT the unfinished side.

    Starting at point A start sewing in and out of the diamond shapes to gather the fabric. You'll continue sewing in and out on all sides until you get to point B.     Sew it to a hair comb.     After you attach it in your hair on the side of your head with bobby pins, then add an embellishment like a flower or feather to cover the comb.     Birdcage veils are made out of Russian Netting or Russian Veiling which is a millinery material. You can usually find it at a really good fabric store or online.     The veiling usually comes in three lengths 9" 12" and 18".     Isn't she gorgeous! If you just want a little coverage over your hair you want 9".     If you want it to cover your eyes, you'll want 12" and if you want it to cover your nose or chin you'll want the 18" veiling (cut it down to 16" to cover the nose.)     It comes in almost every color and you can also find veiling with chenille dots or pearls if you wanted to add embellishment in that way.     Inspired by precious birdcages everywhere! Enjoy!

     

     

    15
  •  

    Photos by: Chelsea Fuss     You will need:  A paper photo album (we used this one from Kolo) works great!  About 1/2 a yard of fabric  Ribbon or string Photo corners Fabric glue Scissors An iron     Take out the ribbon the photo album came with and separate the paper cover and set the pages aside.     Cut a piece of fabric that will cover the outside and inside of the paper photo album cover.     Press the fabric over the paper. Secure the fabric on the inside. fold over raw edges, press them and then secure them to the cover with glue.     Tie together the pages and secure them to the fabric cover with string or ribbon.     For the window opening, cut an X in the fabric and glue the excess fabric underneath the cover.     Secure photos with photo corners.      
    2
  •  

    Concept by: Victoria Hudgins Photos by Erin Holland   Add a dash of confetti to your party in the form of a chandelier! This looks fabulous hung in multiples on top of a dessert bar, or hung individually as centerpieces.     In fact, you can turn your confetti chandelier into a 'cake topper,' who says that a 'topper' has to be placed directly on top of the cake?     Cut out one inch confetti rounds from colored paper. We used about 120 rounds for this installation. I would suggest using a monotone color scheme or 4-5 coordinating colors on each hoop.     Thread the confetti dots together. Begin at the top, leaving enough thread to attach the string to an embroidery hoop. Have your hot glue gun ready and place a tiny drop of glue on the bottom of each dot to hold it in place.     Using an embroidery hoop, tie four to six strings across the top in a criss cross pattern.     One at a time, tie the strands of confetti dots onto the hoop and string base. You can paint or adorn the hoop as needed to match your wedding décor.     Hang the installation above a cake or elsewhere; adjust the length of the strands for just the right balance.      
    17

Get Started!

Create inspiration boards, share ideas with your friends and wedding vendors, get feedback from brides like you, and lots more!

Have a question? Contact Support

Find Your Wedding Vendors

Featured Vendors Near You

Related Photos
Related Forums
What could be more fun than telling your friends and family that you made everything at your wedding yourself? Well, an entire Do it Yourself wedding ...

might be going a bit overboard, but Project Wedding has tons of DIY wedding ideas for you to implement for your big day.

Whether you can’t cut a straight line or you’re the next Martha Stewart, we have DIY wedding ideas for every type of bride. From DIY wedding favors to DIY wedding decorations to DIY wedding invitations, if you’re interested in doing it yourself, we can help! With so many unique images of wedding ideas we’ve found, plus all our great photos of real weddings, you’ll find the most DIY wedding ideas here.

From simple wrap and tie wedding favors to more complex origami wedding decorations – if we think you can make it, you’ll find it here. These DIY favors are guaranteed to thrill your guests without emptying your pockets. Even if you’re not very crafty, we still have some fast and easy project ideas that you might like. And if you have creative friends or relatives, chances are they will be more than happy to help you.

DIY weddings are a great way to put a personal touch on all of your wedding details. You can add your initials to your wedding favors, make a candy buffet that complements your wedding colors, or create a masterpiece that looks store bought but cost way less. Whatever your reason for wanting a Do it Yourself wedding, our articles will help make your dreams come to life.

With so many great DIY wedding ideas, all of your family, friends and honored wedding guests are guaranteed to remember how amazingly creative your wedding day was. Now go get crafty!